Search results

As above, looking for Mongoose 3" tip as I don't like the 5" one i have on it, and also looking for a Laguna front splitter Cheers

just bought a mongoose exhaust and was wondering if the sensor and nut in my old cat is all corroded(spelling??), and wont come out, what do you lads usually do:doh: cheers

As above, I need a radciator in Ireland cheers

Who was it was asking about the group buys on forge front mounts and mongoose exhausts, cant seem to find it anywhere:?

As above, have the engine and box out, anything i should look out to change? Was thinking the water hoses at the back of the block. Also when i turn the wheels from a standstill or very low speed the steering cracks and clonks. Would this be the rack? There was a split in one of the rubber...

On behalf of a mate, The oil light keeps flashing on and off and also the oil pressure guage keeps moving up and down. he says there's no strange noises from the engine and the engine isn't losing oil Any idea's? Cheers8)

As the title says, i need to change the clutch release bearing on my ap organic clutch, and i was wondering if the standard release will do (part no 30502-1W720). For all i know it could even be a standard one that is supplied with the ap organic clutch, cheers Ben

Very bad clonking noise coming from the driveshaft, its still in because the car will still drive. Also when the clutch is engaged, as in foot off the clutch pedal there is a rubbing/grinding noise coming from the box, it stops whenever you put your foot back on the pedal. A little hard to...

Took the R to work today and it was fine this morning, then started it to come home and it was very resitant. Was also idling very low. When you went to accelerate slowly it would be holding back and then it would shoot off, as if you were holding the handbrake on and then letting it off ...

Just starting to fit new whiteline springs 8) How are you supposed to know which springs are for the front and which are for the rear :?:

Couple of questions: Whats the difference in the normal version and the Pro version :?: Approx, cost of buying one from one of the Jap based companies :?: Anyone ever bought one off ebay, and would you recommend it :?: Cheers 8)

Got the R on the dyno on Saturday for the first time. Only have an Apexi induction kit and a Kakimoto exhaust and it gave 246bhp and 244 torque. It was anly running on 0.56 bar Seems a bit high :?

Was out in the R last nite and stopped it for bout an hour, then started it up again to go home, drove about half a mile and it started to splutter and was holding back really badly, got it home cause was only bout another half mile from home and then it conked out when i stopped to reverse...

basically my dads mate bought his son a 95 Sunny 1.5 4 wheel drive :? for his first car I remember coming across one of these on a Jap auction site a while ago Anyway its very high, especially at the back and his dad wants it a bit lower before he gives it to him Will the standard R springs...

The part that the bulb goes into, should there be two or three of the little bits that click into the new side repeater, cause there is 3 on my one and my new clear side repeaters have only got 2 holes :? Cheers

I've just after fitted my willwood 4 pots and discs, along with the braided hoses front and rear. 8) Do you need to bed the pads in for long, cause the brakes dont give a great bite. I bleeded the rears and the 4 nipples on each of the front calipers, but the peddle still doesn't feel...

Just had my engine rebuilt my HKS forged pistons and 1.2mm HG Also had gearbox rebuilt with new 5th, input and layshaft. I've done about 400 miles so far running it in. Been driving under 4,000 revs, the odd time up to 5,000 revs while running it in. 1st gear pulls really well up to...

just wondering if anyone has an exploded view of the gearbox. Im getting mine put back together at the moment and just having a bit of trouble with one of the selectors going in. So anyone have an exploded view of the gearbox cheers :D

I know its been asked before, but did a search, but no defo answers. Which one fits with the goose and which one doesnt, whiteline or cusco 4 point lower brace :?: Just wanna make sure which one fits before ordering. Car is on 16's and will be lowered on whiteline springs Cheers :wink:

I know its about 1,000 miles but if im on standard boost, what rpm should i not go past when im just running the engine in. Its been rebuilt with HKS forged pistons and HKS metal head gasket :wink: