Search results

  1. C

    Manual transmission shift stabilizer bushing

    They are on the OZ and UK eBay sites. Here's the UK link: SHIFT BUSHING Nissan Pulsar Sunny GTiR 4x4 n14 n15 b13 Almera Primera http://bit.ly/ILL6bK
  2. C

    Wtb mudflap, side skirt end cap, o2 sensor connector and front driveshaft

    Looking to buy the following:Drivers side rear mudflapDrivers side side skirt end cap (at the back of the side skirt)Both body parts are ivory white (KJ7). Passenger side front driveshaftO2 sensor (I really just need the loom connector attached to the sensor). The sensor does not have to be in...
  3. C

    Passenger door locks, but won't unlock with remote or door switch

    did you end up sorting this out? My car is having the exact same issues - passenger side will lock but not unlock via power locks.
  4. C

    nearside front/left hand front complete drive shaft

    Ended up finding an outer joint from a shop in the USA. Thanks anyways.
  5. C

    nearside front/left hand front complete drive shaft

    are the middle shafts (between the two joints) usually pretty strong? this joint has been knocking since april and I would get the outer cv joint off ebay, but am wondering about the condition of the middle shaft.
  6. C

    nearside front/left hand front complete drive shaft

    Yeah pm me a quote for the shaft and delivery. postal code s7h4m8. should be all you need. My car was made in november 1991. The joints listed on egay (if they are good quality even) are all for '92+. Do you know if that's going to be a problem? Btw my car does not have abs.
  7. C

    nearside front/left hand front complete drive shaft

    Hello, I was wondering if anyone has a nearside front/left hand front complete drive shaft with boots for sale? My outer boot must have split and my outer c.v joint is now worn and knocking! A price for the part and delivery to Saskatoon, Saskatchewan (Canada) would be very helpful!
  8. C

    How to replace centre gauges with 52mm types (detailed)

    here's a bit of info: I emailed the LMA group and got a reply for them. I don't know what shipping costs to the rest of the world, but £17.29 for shipping alone was enough to make me search somewhere else for the fitting. Anyways, I found one on ebay, it is here...
  9. C

    Small upgrade to GT2860RS/disco potato - MODS?

    Bob, thanks for the offer but this one arrives in 3 days with warranty. too hard to back away from for the price. Could you post or PM me the part number for that turbo? I have GT2860RS - 739548-5 from garrett's website. Also, are you certain the restrictor is located in the housing? Thanks.
  10. C

    Small upgrade to GT2860RS/disco potato - MODS?

    My turbo shit the bed last month. I've come across a GT2860RS for about $1150. Anyways, as for mods/upgrades, the car is bone stock aside from a walbro fuel pump, fmic, ssqv and pod filter. I am wondering about these few questions: 1. will the stock oil and water lines fit with the new...
  11. C

    Aftermarket oil pressure guage - what else is needed?

    bump - does anybody know what thread size and type the standard nissan sensor is? My oil pressure gauge is playing up and its time to change to an aftermarket one. Nissport says it is 1/8 bspt. Can anybody confirm that?
  12. C

    Boost Leaks - How To Test

    If you put the tester onto the metal induction pipe at the turbo, then it will work properly. The pipe from the filter to the turbo inlet doesn't see any pressure aside from the flow rate that the turbo will suck and compress (which is negligible). Put the tester on the metal induction pipe...
  13. C

    twin 12" rockford

    any pictures of said box yet?
  14. C

    original speakers in the doors

    bump - has anybody ever used 5.25" speakers in the front?
  15. C

    Sump gasket sealer

    I applied mine to the pan. I laid a 4-5 mm bead in the groove and then on the inside of the pan around the bolt holes. I did not go around both sides of the holes, just the "inside" side. This picture is not mine, I used the blue permatex stuff. My bead was about half as wide as that one too...
  16. C

    Oil temperature

    bump - what does the stock engine like to run at on the highway when it is hot (25-30*C) outside? Mine is between 90-95 degrees. Is this ok?
  17. C

    Sump gasket sealer

    the manual says to apply the bead in the groove, but make sure you go inside the bolt holes so that oil won't get to the bolts and leak out the threads. You don't do two beads, just one bead.
  18. C

    fitting a short/relocation induction run??

    johnsy, have you got your new pipe made up? If so can you post a picture of it before you install it and another one of it installed? thanks!
  19. C

    Leaky crank seal the story so far...

    are you careful to oil the new seal before putting it in? Also, put it in straight! not one side at a time and lever it in - it must go in with all "sides" at the same rate. I used a pipe the same diameter as it and lightly tapped it in. I posted back in your other thread about removing the...
  20. C

    chain tensioner needed?

    There are links to a few different shops in this thread: make sure you get the 1998+ tensioner as Nissan re-did them then and onwards. http://www.sr20forum.com/general-sr20/251334-how-change-timing-chain-tensioner.html
Top