Search results

  1. G

    Does anyone recognise this plate

    How its sitting at the moment Sent from my SM-G935F using Tapatalk
  2. G

    Does anyone recognise this plate

    Took me ages to round up the intercooler routes looked like someone used tin snips to cut they were very sharp Sent from my SM-G935F using Tapatalk
  3. G

    Does anyone recognise this plate

    I've decided to strip it all back down. Im sending it in soon for acid dipping the whole shell. I also built up the standard engine back up replacing all seals got cosworth gasket as well not looking to push too much in the standard block though. The car will be returned back to ivory again as...
  4. G

    Speedo meter not working and kms not ticking over ?

    Give it a little twist left to right and pull upwards Sent from my SM-G935F using Tapatalk
  5. G

    Speedo meter not working and kms not ticking over ?

    Yes Sent from my SM-G935F using Tapatalk
  6. G

    Speedo meter not working and kms not ticking over ?

    Sometimes the gear on the speedo gets chewed off or drops off. Best to take it out using 10mm socket Sent from my SM-G935F using Tapatalk
  7. G

    Speedo meter not working and kms not ticking over ?

    Check wiring to dizzy and make sure its got ground on dizzy body. That was the issue with mine. Sent from my SM-G935F using Tapatalk
  8. G

    Gtir overheating after installing thermostat?

    Brilliant buddy Sent from my SM-G935F using Tapatalk
  9. G

    Gtir overheating after installing thermostat?

    If the temperature switch is ok then will be relay. Sent from my SM-G935F using Tapatalk
  10. G

    Gtir overheating after installing thermostat?

    Do compression check as well Sent from my SM-G935F using Tapatalk
  11. G

    Gtir overheating after installing thermostat?

    I didnt really have that issue either. Just got to make sure system is flushed proper no blockages. Make sure the cooling fans work as plenty of people have the issue when the fans dont kick in Sent from my SM-G935F using Tapatalk
  12. G

    Gtir overheating after installing thermostat?

    Cool hopefully he should located it i checked on the engine i have and its all bare so i wasn't sure but good that you've help Johnny Sent from my SM-G935F using Tapatalk
  13. G

    Gtir overheating after installing thermostat?

    Its a screw or bolt im not at my pulsar today so cant confirm but ill check on the other engine i got. Just out shopping so will defo look at it in 30 mins. Sent from my SM-G935F using Tapatalk
  14. G

    Gtir overheating after installing thermostat?

    I think if i remember theres a screw that you take out to bleed system. Someone else will prob confirm this. Sent from my SM-G935F using Tapatalk
  15. G

    Gtir overheating after installing thermostat?

    If the fans dont work that will be a big problem on cooling the engine Sent from my SM-G935F using Tapatalk
  16. G

    Gtir overheating after installing thermostat?

    Do a compression test 1st then determine if headgasket. You could also try k seal. But if its overheating the fans should cut in Sent from my SM-G935F using Tapatalk
  17. G

    Gtir overheating after installing thermostat?

    As above either airlock or you've got a headgasket problem Sent from my SM-G935F using Tapatalk
  18. G

    forged engine wanted

    Just bought one literally now 2.2 stroker kit thanks guys Sent from my SM-G935F using Tapatalk
  19. G

    forged engine wanted

    I'm after 86mm Sent from my SM-G935F using Tapatalk
  20. G

    forged engine wanted

    ideally looking for a forged engine already built or any forged internal parts
Top