right have not got the patience to carry on with this bloody thing! timing is slighty out i think
was thinking of putting it on for about two thousand five hundred am i taking the pi££ at that amount should i be aiming slighty or a lot lower
http://s299.photobucket.com/albums/mm312/povanic/...
Hi All
Plug in me conzult and went for a drive yesterday
Looks really good with the bright colours going up and down numbers changing and so on.
but what the H@ll does it all mean lol
what should the car show for its sensor values at idle
I know
TPS should be between .44 and .50
But...
right set the car timing to 18 degree instead of 20, to be on the safe side as recomended by Bobby boy, now got popping/bang noise when i take my foot of the the accelerator.
what do i look at to stop this, as its scares the shi@ out of pedestrians and i can see the fuzz pulling me over
took the top of the tank to play with the fuel float as i think it was stuck and for the life o me i cannot remmeber how the bloody seal goes back in:doh:
it will not fit inside the hole as its about 2cm too big and i am sure it did to make the top air tight.
can some one please enlighten me...
Hello all
Have wired dash wire number 6 to my new dash filled up me fuel tank and its still reading empty.
Have taken off the two pin plug on the fuel tank and the ohms reading is 87ohms which i also beleive is close to empty
would a poor earth make the reading 87 ohms and if so where is the...
what could of made the top of the pistons look like the moon they have craters all over them
no burn marks or carbon.
looks like it going to the scrap heap in the sky lol
If my TPS ws out when Ed mapped my car (0.15)
Now that i have adjusted it to 0.45 would this over fuel the bloody thing. Adjusted it friday and put new leads on her and now it stinks of fuel when running.
Could the holes drilled in this pulley have been put there as timing marks
or just to balance the pulley out.
Cannot find any other marks on the bloody thing.
well purchased an acewell dash to replace my dead gtir clocks
in the end went for this one
http://www.acewell.co.uk/Acewell%20Speedometers/ACE-7xxx/ACE-7659.htm?action=full&id=66
If it works will put up some pictures up hopefully will try getting it in on Sunday.
they seem to work a bit...
Hi does anyone know what type of sensor we have, i know its electrical, need to know if its a Hall effect sensor & generate a square wave with a voltage of at least 2.7V
Any help would be great
Thanks
right purchased some universal window switches<BR>for the life of me cannot get these to work surely they dont have to be nissan units, i know the units in the door came with lots of electrical crap in them, is that stuff really needed <BR><BR>just want to put 2 simple switches...
so i have a meter and half left of ofc competition grade 20mm2 power cable left, so was thinking of changing the alternator cable
does the alternator cable go to the starter first and then the battery or is it direct from alternator to battery
2nd alternator of Mr Bob started with 14.4v now down to 13.4 after a short drive and still droping
got the dash out but where do i start to look for electrical problem could it be poor earths, a nakerd Battery, or case of having to pay a bloody electrian
few things left to fix
speedo works, fuel gauge and water temp, but have no rev meter
where is the sender for the rev meter !
Or is it case of the dash is fu@ked
thanks all
Has any one used one before
my radtec rad went bang and they wanted £360 for a recore no thank you
Berkshire radiators are now going to make me up a identical custom copper rad but with a 42mm core and with 18fins per inch so it flows alot better
he was a bit worried thou a copper rad...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.