Search results

  1. A

    Light clutch pedal

    I've always like the gt4 and I love a rare car but not sure I want an old car again. I hate chasing rust
  2. A

    Light clutch pedal

    But if I reduce the size of the slave surely were getting back to where we started. Never hear of or seen one. Googled in and it's not really my cup of tea mate.
  3. A

    Light clutch pedal

    Is it a gt4? i've just got it off. No so bad only took half hour measured the travel and the original is 30mm approx and the new is about 32mm. So maybe I would need closer to 40mm to make it work?
  4. A

    Light clutch pedal

    It's working but there's not enough travel. With a smaller bore master there's is less fluid moved so the slave will not travel far enough to disengage the clutch. It's a new clutch line from master to the slave. It looks clean inside the slave behind the boot and if you push it in, it comes...
  5. A

    Light clutch pedal

    I don't think its right but was doing the job before. I've got a .5 bore on there now
  6. A

    Light clutch pedal

    Ok I'll do that next week when I refit the original. There's not enough travel on this one
  7. A

    Light clutch pedal

    Is there any sort force multipler that can be installed between the original master and slave?
  8. A

    Light clutch pedal

    I have no idea how to estimate force. My leg strength isn't average so it's not a good guide. Do you work with hydraulics?
  9. A

    Light clutch pedal

    I maybe get a 1/4 inch before it gets too hard to move. I don't want to use to much force as I'm going against the thermostat housing. It's got to be a heavy clutch cover causing it
  10. A

    Light clutch pedal

    The slave looks like that. The rod just didn't look right. I think it's just to much load for the master. It' was fine till I adjusted the rod is out of alignment as it's adjusted to the end of the rod to make it work. The fork moves . The little slack there is, you can see it's not seized
  11. A

    Light clutch pedal

    It did feel lighter but I think that was just taking up all the free play. I started looking at removing the slack between slave and fork. Is this the right slave rod? Looks like a chopped up bolt. I've fitted nuts on it so the nuts sit on the edge of the piston and adjusted. It now works but...
  12. A

    Light clutch pedal

    Just an update. Fitted the new master cylinder and it doesn't work. Don't seem to have enough movement of the slave to disengage the clutch. So will have to put it back to original and maybe sell it
  13. A

    Light clutch pedal

    So found this Banjo https://www.ebay.co.uk/itm/150619648046 And I'll use is with this Banjo bolt https://www.ebay.co.uk/itm/172957362529 Can anyone see a problem with that? That should allow me to use an8 hose to push on the reservoir
  14. A

    Light clutch pedal

    That's it. I've got to try. I'm just trying to find a way of using the original reservoir, but it's a 1/2 hose and need to go down to 7/16 fittings and only a limited distance between the 2. I'm hoping I can get away with a braided line going to the slave. Thanks for your help and ideas
  15. A

    Light clutch pedal

    That is an idea, but I would prefer to fit a clevis that's made to fit. Everything I do is easily reversible if It should be put back to original. Hopefully will get an answer Monday and they sell the master cylinder too so will order both together
  16. A

    Light clutch pedal

    Well I've got it off. Found out the pushrod is an m8 thread so will need a new clevis to fit. I may have found one but there's no info on the size of the pin so waiting to hear back from them
  17. A

    Light clutch pedal

    Ok. Well I couldn't find any the same size do decided I'm gonna make a plate and weld some studs on so I can fix the plate using original studs and bolt new cylinder to the plate. I will probably get it off at the weekend and see what's what. I think for 40 quid it's worth a shot
  18. A

    Light clutch pedal

    Do they still hold the power. Think I'm gonna try a new master cylinder first as it'll be easier than dropping the box. If it doesn't work I will get in contact with helix. Thanks mate
  19. A

    Light clutch pedal

    Thanks mate. I will Google and see if there are any others with 70mm centers
  20. A

    Light clutch pedal

    Think he only way I will get the dimensions is to take mine off. It's quite handy, that ebayer is only up the road from me so I can take mine and compare if I can't find any dimensions
Top