Search results

  1. T

    Running engine wanted

    Hello! i want a running engine OEM or forged. Please send me PM if you have one for sale. Thanks Sascha
  2. T

    Low Oil pressure after rebuild

    Hi, i still have a problem with the oil pressure. Few months ago i had low oil pressure at all revs. Then i had put the engine out of the car and rebuild them. I had fit another block with new Mahle pistons, acl bearings and a new oil pump. After rebuild the oil pressure is same as...
  3. T

    T3 exhaust manifold wanted

    Hi, i want a T3 exhaust manifold! Please send me PM if you have one for sale. Thanks Sascha
  4. T

    Oils squirters and Mahle pistons don´t work?

    Hello! i have a big problem. The oil squirters have contact at the bottom of the Mahle piston. Can i turn the squirters a little that it can work without problems? Thanks Sascha
  5. T

    NEW 1.8mm head gasket wanted

    Hi, i want a new 1.8mm head gasket. Please send me pm if you have one for sale. Thx Sascha
  6. T

    Where can i get a alignment tool for clutch fitting?

    Hello! Where can i get a alignment tool for clutch fitting? Thanks Sascha
  7. T

    Wanted 1x 87mm HKS piston

    closed Closed
  8. T

    Twin plate clutch discs problem

    Hi, i have fit a Sachs sintered twin plate clutch in my car and now i have a set of inner and outer plates from Helix for rebuild. http://www.demon-tweeks.co.uk/motorsport/race-rally-clutches/helix-7-25-sintered-drive-plate-inner...
    • Thor
    • Thread
    • Replies: 6
    • Forum: Clutch
  9. T

    Small end bush exchange??

    Hi all! At the overrun is light knock and danny (red reading) told me few months ago that maybe is the small end bushes of the rods. Now my question, is it possible too exchange these on the tomei rods and where i could get the bushes?? Or use i better the OEM rods again? Thanks sascha
  10. T

    Wanted forged engine

    Hello! i want a forged engine or complete block! Please send me offer PM Thx Sascha
  11. T

    Injectors wanted! 800cc or bigger!

    Hello! i want a set of 800cc or bigger injectors! please send me PM if you sell these! regards sascha
  12. T

    Denso/Sard 1000cc and more fuel pressure

    Hello! a friend of me told that then i give the injectors more pressure it is much better spray for the injection but i don´t can find more detail about mine 1000cc Denso injectors. At the moment i have set the duty @ 44,4% and lag 0.08 @ 43.5psi (3Bar) fuel pressure. What i must adjust...
  13. T

    Engine harness wanted

    Hello! i need a engine harness where the connectors all ok. If you have one please send me PM. Sascha
  14. T

    Torque settings wanted for head bolts with MLS head gasket

    Hi, i need the right torque settings for the head bolts if i fit a metal head gasket! If i fit the metal head gasket i must loosen the bolts and torque again with turn angle? Thanks Sascha
  15. T

    Connectors from wiring wanted

    Engine wiring wanted Hi! i want a engine wiring without damaged connectors! Thanks Sascha
  16. T

    Combustion Chamber Volume details at the head wanted

    Hello! i want for calculate the thickness of the HG the Combustion Chamber Volume from the std head. Can anybody tell me how much cc it is? cheers Sascha
  17. T

    ARP Head stud set wanted

    Hello! i want a set of Arp head studs! Please send me PM if you have them for sale! Cheers Sascha
  18. T

    NEW Head gasket 1.1mm or 1.0mm or 0.8mm wanted

    Hi @ all! i wand a new metal head gasket with 0.8mm or 1.0mm or 1.1mm thickness specific for the GTI-R! If anyone has it for sale please send me PM. regards Sascha
  19. T

    Uprated rods wanted

    Hello! i want uprated rods for the GTI-R for using the 19mm bearings or makes it difference when using 17mm? regards Sascha
  20. T

    What is the PCD of the brake rotors?

    Hello! I must order new Hispec rotors but i don´t know where i must measure the PCD! Can anybody tell what is the "PCD" of the brake rotors? Cheers Sascha
    • Thor
    • Thread
    • Replies: 6
    • Forum: Brakes
Top