hi does anyone know if when raising the fuel pressure to 4 bar do the injector lag times stay the same or get less or more? im trying to setup my 700cc injectors correctly at 4bar i have the increase in size to 808cc which is approx 54 in the power fc but im unsure if the lag times should stay...
hi i am having as problem with this setup and i am in need of some advice/help basically i have the system installed and i have a misfire at 2000rpm all loads/all gears the a/f gauge goes really lean and sometimes even off the scale i have a pfc fitted and i have set the dwell times to 1.7ms but...
hi really just a post to see if anyone else is suffering i filled up from cold at southend shell opposite the bell - i filled up from empty and about five miles down the road it lost all power then come back to life then another few hundred yards did the same then was ok, then the next day...
hi my 700cc injectors seem to be maxing out at high revs i dont really want to spend out on a new set of injectors especially as it seems larger ones need the rail drilling out or different plugs etc so i thought i could just raise the fuel pressure to 4 bar how do you work out what to enter in...
hi just got this delivered today and need a bit of advice to set it up,
1)which wire do you use for the cylinder select wire it says a thin switch 12v, is that just an ignition supply
2) can you remove the old ignition amplifier etc after fitting or do you leave it still connected (and is...
hi my mintex 1144s are far too noisey they really make a horrible metal grinding noise in traffic making it embarrasing to drive ive tried everything inc grease/chamfering etc but its always the same apparantly mintex are noisy
are there any pads that give the same braking response but...
has anyone ever solved the problem of where you turn a corner and then push the brake pedal and on the first push it sinks to the floor, second is fine??
i find lots of references to it on a search but no one seems to have found a reason
ive just put my hispecs on and pressure bled them...
hi just a quick question really i am in the process of running in my new engine having covered 200 miles now, i has 87mm hks pistons dp exhaust manifold and am performance elbow with a 3071r sandwiched between all lagged
i have read that these turbos are hitting full boost at around 3k but...
hi bit of a silly question really but hope someone can help i have a sard fpr and am a bit confused about which way the lines go, is it from the fuel filter line goes to the regulator then the reg goes to the rail where the old regulator fits then rail back to return to tank
i have a pressure...
hi i have recently fitted my emanage ultimate and set it up how i thought it should be for standard injectors and z32 airflow sensor however it seems to massively overfuel the a/f at idle is 10.0 when i drive it there seems to alot of popping and banging on overrun and a bit of black smoke on...
as above really they have hks sr20 stamped on them with part number b05 x001 and x002 on the cam before the 1st lobe
also on the other side from the sr20 bit iot has r1 stamped
any ideas on what these are:lol:
do the hks 264 have the 2202-ex001 and ex002 stamped on the cam?
hi have totally finished my new engine now, just waiting for the weekend to put her in, one thing has me a bit worried though the turbo elbow is very nearly touching the alternator its about half a centimeter away from it,do you think i need to get some sort of heatshield made up or lag the...
hi i have the said combo above but the turbine wheel is too large on the 3071 for the elbow by 10mm someone must of fitted these two together what do you have to do to get them the same size, is it a job of cutting it all out to fit and rewelding the pipework, or just lopping of the guide into...
hi i have now got my 3071r (i think) but just want to check the part number to make sure its correct, can someone post up their number off the metal plaque, i assume this is the part number?
hello, i have checked the clearance on the camshafts etc and req the following:
shims
2.45, 2.60, 2.40x2
guides
2.40, 2.50, 2.42, 2.60
if anyone has these spare please can i have them:-D :thumbsup:
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.