Search results

  1. D

    Rear Window Push in Trim - B Pillar

    Hi All, I'm after this piece of trim for the passenger side of the vehicle as shown below. Its a push in plastic piece as shown on the "Driver's side" image. This is in the door shut / b-pillar. Anyone got one for sale? Cheers, Steve.
  2. D

    Any places you recommend for Arch Rolling?

    Hi Everyone, Due to having some new rear arches (5 door) fitted as part of my R's refurb the inner lips stick in to the wheel arches more than the OEM 3 door arches and are slicing into my tyres (205/45 r16). I don't need much material rolling in at all, but slicing into freshly painted arches...
  3. D

    Door Seals and Slam Panel Vertical Support wanted

    Hi there ! I'm hoping you can help - my Pulsar is at the paintshop and needs a couple of bits to finish it off - please see below : Please note the door seals need to be intact, no rips or tears and be in very good condition with plenty of life in them. 1) Driver and Passenger Door to car...
  4. D

    An Ashtray!

    Anyone got a spare one...as clean/mint as possible as I'm not a smoker! Cheers, Steve.
  5. D

    R been in storage 2years+ , need advice for getting it started!

    Hi Folks, A lot of time has passed since my ‘R was last on the road, but now being better off financially means the Beast can finally return to the road! :-D :twisted: What I’m after is any advice anyone might have for getting it running ; changing all fluids (coolant, oil, clutch, brake...
  6. D

    Wanted - Aftermarket Struts

    Hi All, I'm looking for a set of aftermarket struts, either just the front 2 or all 4 struts (with springs if all 4, if only the front 2 then I'm easy either way!) . Wanted with no leaks and in decent condition. Please reply or PM me if you got what i need! :-D Cheers :thumbsup: donpulsar :-)
  7. D

    Koni Inserts

    Hi everybody, Apologies if this has been asked before, but could anyone tell me if Koni inserts are still available for standard GTiR shocks & if so - where could i get some from ? Thanks in advance! :thumbsup: donpulsar :-)
  8. D

    Front and Rear Wishbone Bushes - where from ?

    Just a quick one folks but I'm after the Front and Rear bushes for the front wishbones, and poss. all the anti-roll bar ones too ; can anyone give me a few pointers as to where's best to get them from ? All my local motorist discount had was the whole wishbone arm for £83.00, whilst Supaflex's...
  9. D

    Strange steering wheel behaviour...

    I'm having a weird problem that none of my mechanically minded mates can solve so wondering if anyone here can suggest a solution - here goes... I get in the car and startup, no probs. Reverse the car out of the drive and onto the road. Still no probs. When i set off down the road the car is...
  10. D

    Big Thanks to the following members!

    Following my oil feed pipe splitting (and dumping half my oil down the M18! :shock:), i decided to get a few things sorted out on the 'R (and as usual found other stuff broken along the way :doh:) so i'd like to say a big thanks to the following members : pulsarboby - for the tips and...
  11. D

    Anyone running a Forge Actuator ?

    Hi all, Have just got hold of one of these and it has a blue spring in it (well, grey with a blue stripe!). The website rates the spring at 12.5-17psi (0.8-1.1 bar). Does anyone know what boost pressures you're able to run upto on this spring ? Or what colour springs are people running with...
  12. D

    Need help identifying my turbo...

    Hi Folks, Hoping one or more of you turbo guru's can help me out! Due to the oil feed pipe cracking the turbo's out of the car at the moment and this where my query starts ; can anyone help me to identify my turbo ? I was told it was a GT2871R when i bought it off but having had a good look at...
  13. D

    Manifold Studs + Nuts,Lambda sensor & 1 bar actuator

    UPDATED : Wanted ASAP! 1-8 Manifold Studs - Ordered from Nissan :cry: 8 Manifold Stud Nuts - Ordered from Nissan :cry: Lambda sensor (3 wire, with or without connector) - thanks to J44MA for this :thumbsup:(if my R doesn't like the sensor I'll be in touch EssexAaron) 1 bar actuator (straight...
  14. D

    Whats Max Boost on a Profec B ?

    Before you ask, not a Spec 2, but the old skool Profec B (black and see thru' blue). I'm hitting a boost ceiling of 1.6 bar (23 psi) and can't go any higher. From what i've read, the lo boost should max out around 1.2 bar (which mine does) but cranked up the hi boost tops out at 1.6 bar...
  15. D

    Wont run more than 1.6bar

    Now then, I'm having problems with my boost in that it won't go higher than 1.6 bar. :cry: I'm running a GT2871R & I'm currently using a GReddy Profec B Boost controller (not Spec 2). At the highest setting on "High boost" I get a peak of 1.7 bar before returning to 1.6 bar. Experimenting with...
  16. D

    Help from anyone running water/methanol injection

    Hi there, Have bought a "Devils Own" water/methanol injection kit and it looks like a decent bit of kit :twisted: - I'm wondering if anyone could post up pics / descriptions of where they mounted their kit (pump, pressure switch, nozzle and if applicable water bottle) and what benefits etc...
  17. D

    Problems ordering parts @ Nissan Dealers

    Hi all, I don't know how many people have found this out already from experience, or have read from a previous post that Nissan have changed the way the majority of us can order any bits we may need from them. (and prices for Pulsar GTiR parts are different than for the UK Sunny GTiR parts - in...
  18. D

    Standard Airbox

    Hi folks, Pretty simple one this ; I'm after a standard airbox. I'm after one in decent condition with all it's clips and with NO extra holes (drilled or otherwise) and no cracks, chunks missing etc. If anyone happens to have one please let me know! :thumbsup: Cheers, donpulsar :-)
  19. D

    Would a Collins Esc.Cossie actuator fit an 'R?

    As above..found 1 cheap but need to kno if it'll fit my GT2871R ? Cheers and thanks in advance, donpulsar :-D
  20. D

    Drop in turbo boost - how do i cure it ?

    Right then, one for anyone who's technically minded about turbos. My spec for the turbo side is : Tubular Manifold, GT2871R, standard 0.65 bar actuator, 3" Janspeed Turbo Elbow + 3" Janspeed Exhaust system w/ 1 silencer. Boost controlled by GReddy Profec B (and yep, these have no atmospheric...
Top