Search results

  1. D

    Garrett GT2871R

    Cathode - Running a Dastek piggyback ECU with a Z32 MAF on there. Bearing in mind that it was done over 10 years ago it still works very well. The restriction after uprating the turbo (on the intake side) is the maf and injectors. I guess new ECUs these days can use a different MAF as there's...
  2. D

    Any places you recommend for Arch Rolling?

    Yep I definitely want them rolled but cant find anywhere local to me. A place in Sheffield (M-Tec) does it but really dont want my money! They tell me they dont do Saturdays, they offer me days they can do it, then when I try and book a day they tell me the engineer is having a site meeting and...
  3. D

    Garrett GT2871R

    Anytime Cathode :blush: With that turbo, 1.6 bar boost with 550cc inj & an Evo6 FMIC I'm running 380bhp/325 lbs ft torque!
  4. D

    Rear Window Push in Trim - B Pillar

    Hi All, I'm after this piece of trim for the passenger side of the vehicle as shown below. Its a push in plastic piece as shown on the "Driver's side" image. This is in the door shut / b-pillar. Anyone got one for sale? Cheers, Steve.
  5. D

    Any places you recommend for Arch Rolling?

    This is the amount of shred...so far - not a lot! Wondering if a downsize to 195/45 r16 would do the trick, or adjust my camber at the back?!
  6. D

    Any places you recommend for Arch Rolling?

    Hi Everyone, Due to having some new rear arches (5 door) fitted as part of my R's refurb the inner lips stick in to the wheel arches more than the OEM 3 door arches and are slicing into my tyres (205/45 r16). I don't need much material rolling in at all, but slicing into freshly painted arches...
  7. D

    Garrett GT2871R

    Nice turbo - I have this on mine with a 0.63 a/r, brilliant response and power capabilities. I tried to use my existing std actuator which couldn't handle the extra boost I needed, so replaced it with a 1 bar Forge Actuator - another great piece of kit. Replace it with a decent aftermarket one...
  8. D

    Door Seals and Slam Panel Vertical Support wanted

    Hi there ! I'm hoping you can help - my Pulsar is at the paintshop and needs a couple of bits to finish it off - please see below : Please note the door seals need to be intact, no rips or tears and be in very good condition with plenty of life in them. 1) Driver and Passenger Door to car...
  9. D

    An Ashtray!

    pulsarboby - you have PM lakeview - let me know what you find in your garage topdoggtir - your inbox is full!
  10. D

    An Ashtray!

    My inbox was full - sorry! Please PM me :-)
  11. D

    An Ashtray!

    Anyone got a spare one...as clean/mint as possible as I'm not a smoker! Cheers, Steve.
  12. D

    R been in storage 2years+ , need advice for getting it started!

    Got started on Sunday...it's been a while! Cracked the bonnet open...looking fairly clean to say its been sat in the garage for 2 years - Checked oil levels, coolant then removed all sparkplugs and put a drop of oil down each bore. Left for just under an hour to soak, added some fresh...
  13. D

    R been in storage 2years+ , need advice for getting it started!

    Cheers for the input everybody, really appreciate the replies :-D The 'R has been dry stored in my garage for the 2 years and yep the handbrake is off! If the weather's nice tomorrow then I'll be making a start...wish me luck!
  14. D

    R been in storage 2years+ , need advice for getting it started!

    Hi Folks, A lot of time has passed since my ‘R was last on the road, but now being better off financially means the Beast can finally return to the road! :-D :twisted: What I’m after is any advice anyone might have for getting it running ; changing all fluids (coolant, oil, clutch, brake...
  15. D

    intercooler and cc setup...

    I tested a Subaru Legacy chargecooler setup on my 'R (was a cheap way to give the chargecooler option a try!) with my GT2871R, but it couldn't keep the temperature down as much as my Evo 6 FMIC does. I think however, that was more down to the water capacity of the Legacy system and the speed the...
  16. D

    standard front bumper and bumper bar

    Have got a standard front bumper, uncut and unpainted. No towing eye or mesh inserts. It has silver spray paint on the inside (not a problem if you're painting it anyway ;) ) It also has a couple of small cracks (easily repaired with fibreglass/plastic welding) but it's yours for £15 + p&p. If...
  17. D

    Wanted - Aftermarket Struts

    Am interested - do let me know once they become available. What mileage have they covered? Cheers, donpulsar :)
  18. D

    Wanted - Aftermarket Struts

    Hi All, I'm looking for a set of aftermarket struts, either just the front 2 or all 4 struts (with springs if all 4, if only the front 2 then I'm easy either way!) . Wanted with no leaks and in decent condition. Please reply or PM me if you got what i need! :-D Cheers :thumbsup: donpulsar :-)
  19. D

    Koni Inserts

    Do you have a contact number for Woodford Garage ? Cheers :)
  20. D

    Koni Inserts

    Hi everybody, Apologies if this has been asked before, but could anyone tell me if Koni inserts are still available for standard GTiR shocks & if so - where could i get some from ? Thanks in advance! :thumbsup: donpulsar :-)
Top